Welcome to my blog!  I hope you like butterflies because this card come from a new suite by Stampin UP® called Butterfly Kisses!  Now the Designer Series Paper is very bright and makes you smile but I wanted to make a card for all my purple lovers out there!
I know its hard to see but I used the Brick & Mortar 3D embossing folder on the Basic White piece on the front of this card.  I could not get a good picture of it but in person it looks stunning!
Below you will find the card cuts, instructions, supply list and a link to a video I did for this card and one other using the brighter colors!  Enjoy!
Don’t forget to sign up for my newsletter to keep updated on all my new card designs and Stampin Up® goodies!
Card cuts: Card Base = Fresh Freesia – 5 1/2 x 8 1/2 scored at 4 1/4
Card Stock = Basic White – (2) 4 x 5 1/4, 1 1/2 x 3
= Fresh Freesia – 3 x 5 1/2 & 1 1/8 x 5 1/4
Designer Series Paper (DSP) = Butterfly Kisses – 1 x 5 1/8 & 1/2 x 4
Die Cutting/Embossing:
1.  From the 3 x 5 1/2 Fresh Freesia piece cut the following at the same time: 
A.  Using the Build a Butterfly Dies – cut one large and one small detailed Butterfly.
B.  Using the Deckled Rectangle Dies – Cut the second to the smallest die
2.  From the 1 1/2 x 3 Basic White piece – Cut out the smallest Deckled Rectangle Die
3.  Run one of the 4 x 5 1/4 Basic White pieces through the Brick & Mortar 3D embossing Folder.
4. Using the Fresh Freesia ink do the following:
A.  Place the front sentiment onto a block then mask off the word “vibes” ink up with the ink pull off mask then stamp onto the Basic White Deckled piece as far to the top as you can fit it.
B.  Then mask off the words “Sending good” ink up with the ink pull off mask then stamp the word “vibes” as shown just below “Sending good” 
5.  On the other 4 x 5 1/4 Basic White piece stamp the inside sentiment as shown.
6.  Adhere the Brick & Mortar Basic White piece to the card front.
7.  Adhere the DSP strip to the 1 1/8 x 5 1/4 Fresh Freesia strip, then add both to the card front about 1/2″ from left edge of Brick & Mortar piece and flush on the top and bottom.
8.  Using Mini Dimensionals down the back of the bodies on the Butterflies adhere them to the card front as shown. 
9.  Adhere the stamped Deckled Label to the Fresh Freesia Label then add both to the card front as shown. (Note: use dimensionals on the back of the right side and liquid glue on the back of the left side to keep it level)
10.  Apply Basic Pearls to the Butterflies on the card front. (Note: I used medium pearls for the large butterfly and small pearls for the small butterfly)
11.  Apply the Fun Flowers Resin Shapes to the sentiment label as shown. 
12.  Adhere the 1/2 x 4 DSP strip to the bottom of the stamped 4 x 5 1/4 Basic White piece then adhere both to the inside of the card as shown. 
All done!
Supply list:  (Note if you’d like to order any supplies just click on any of the pictures below to go to my online store)  I have listed all the individual products in the suites as well as the suite to simplify ordering!

Product List

Butterfly Kisses Suite Collection (English)

Best Butterflies Bundle (English)

Deckled Rectangles Dies

Brick & Mortar 3D Embossing Folder

Butterfly Kisses 6" X 6" (15.2 X 15.2 Cm) Designer Series Paper

Fresh Freesia 8 1/2" X 11" Cardstock

Basic White 8 1/2" X 11" Cardstock

Fresh Freesia Classic Stampin' Pad

Fun Flowers Resin Shapes

Pearl Basic Jewels

Mini Stampin' Dimensionals

Multipurpose Liquid Glue



Don't miss out!
Subscribe To Newsletter
Receive top Stamping news, class schedules, card making tips and more!
Invalid email address
Give it a try. You can unsubscribe at any time.